ATSAM4E-EK

Description

Atmel's SAM4L series is a member of a family of Flash microcontrollers based on the high per formance 32-bit ARM Cortex-M4 RISC processor running at frequencies up to 48MHz.
The processor implements a Memory Protection Unit (MPU) and a fast and flexible interrupt controller for supporting modern and real-time operating systems.

Features

• Core
– ARM® CortexTM-M4 running at up to 48MHz
– Memory Protection Unit (MPU)
– Thumb®-2 instruction set
• picoPower® Technology for Ultra-low Power Consumption
– Active mode downto 90µA/MHz with configurable voltage scaling
– High performance and efficiency: 28 coremark/mA
– Wait mode downto 3µA with fast wake-up time (<1.5µs) supporting SleepWalking
– Full RAM and Logic Retention mode downto 1.5µA with fast wake-up time (<1.5µs)
– Ultra low power Backup mode with/without RTC downto 1,5/0.9µA
• Memories
– From 128 to 512Kbytes embedded Flash, 64-bit wide access,
• 0 wait-state capability up to 24MHz
– up to 64Kbytes embedded SRAM
• System Functions
– Embedded voltage linear and switching regulator for single supply operation
– Two Power-on-Reset and Two Brown-out Detectors (BOD)
– Quartz or ceramic resonator oscillators: 0.6 to 30MHz main power with Failure
Detection and low power 32.768 kHz for RTC or device clock
– High precision 4/8/12MHz factory trimmed internal RC oscillator
– Slow Clock Internal RC oscillator as permanent low-power mode device clock
– High speed 80MHz internal RC oscillator
– Low power 32kHz internal RC oscillator
– PLL up to 240MHz for device clock and for USB
– Digital Frequency Locked Loop (DFLL) with wide input range
– Up to 16 peripheral DMA (PDCA) channels
• Peripherals
– USB 2.0 Device and Embedded Host: 12 Mbps, up to 8 bidirectional Endpoints and Multi-packet Ping-pong Mode. OnChip Transceiver
– Liquid Crystal Display (LCD) Module with Capacity up to 40 Segments and up to 4 Common Terminals
– One USART with ISO7816, IrDA®, RS-485, SPI, Manchester and LIN Mode
– Three USART with SPI Mode
– One PicoUART for extended UART wake-up capabilities in all sleep modes
– Windowed Watchdog Timer (WDT)
– Asynchronous Timer (AST) with Real-time Clock Capability, Counter or Calendar Mode Supported
– Frequency Meter (FREQM) for Accurate Measuring of Clock Frequency
– Six 16-bit Timer/Counter (TC) Channels with capture, waveform, compare and PWM mode
– One Master/Slave Serial Peripheral Interface (SPI) with Chip Select Signals
– Four Master and Two Slave Two-wire Interfaces (TWI), up to 3.4Mbit/s I2C-compatible
– One Advanced Encryption System (AES) with 128-bit key length
– One 16-channel ADC 300Ksps (ADC) with up to 12 Bits Resolution
– One DAC 500Ksps (DACC) with up to 10 Bits Resolution
– Four Analog Comparators (ACIFC) with Optional Window Detection
– Capacitive Touch Module (CATB) supporting up to 32 buttons
– Audio Bitstream DAC (ABDACB) Suitable for Stereo Audio
– Inter-IC Sound (IISC) Controller, Compliant with Inter-IC Sound (I2S) Specification
– Peripheral Event System for Direct Peripheral to Peripheral Communication
– 32-bit Cyclic Redundancy Check Calculation Unit (CRCCU)
– Random generator (TRNG)
– Parallel Capture Module (PARC)
– Glue Logic Controller (GLOC)
• I/O
– Up to 75 I/O lines with external interrupt capability (edge or level sensitivity), debouncing, glitch filtering and slew-rate control
– Up to Six High-drive I/O Pins
• Single 1.68-3.6V Power Supply
• Packages
– 100-lead LQFP, 14 x 14 mm, pitch 0.5 mm/100-ball VFBGA, 7x7 mm, pitch 0.65 mm
– 64-lead LQFP, 10 x 10 mm, pitch 0.5 mm/64-pad QFN 9x9 mm, pitch 0.5 mm
– 64-ball WLCSP, 4,314x4,434 mm, pitch 0.5 mm for SAM4LC4/2 and SAM4LS4/2 series
– 64-ball WLCSP, 5,270x5,194 mm, pitch 0.5 mm for SAM4LC8 and SAM4LS8 series
– 48-lead LQFP, 7 x 7 mm, pitch 0.5 mm/48-pad QFN 7x7 mm, pitch 0.5 mm